Funct. Mater. 2024; 31 (4): 508-515.

doi:https://doi.org/10.15407/fm31.04.508

Effect of thermal spraying of different ceramic coatings on rotational fatigue life of AISI 1020 alloy

Saad Gh. Rifai, Edrees E. Khadeer

Department of Physics/ College of Science/ University of Mosul

Abstract: 

The effect of thermal coating of AISI 1020 alloy substrate on the fatigue life during rotation was studied in comparison with the fatigue strength of the substrate. A rotating fatigue tester (HSM 19) was used to test the specimens at room temperature. Fatigue tests were carried out at various stress levels to obtain S-N curves. Two coatings were applied to the AISI 1020 steel alloy using thermal spraying method: a NiAlCrSi bonding coating and a thermal barrier coating based on an alloy (Al2O3+MgO). The microstructure and phase composition of the coatings were investigated using SEM and XRD methods. Compositional analysis revealed the presence of numerous precipitates and primary phases, including Al2O3, Cr2O3, and CrNiO4, nickel or chromium secondary phases, as well as different oxides like CrMgO4. The morphological results also show that the coating was quite heterogeneous, with a significant concentration of oxide inclusions, pores and microcracks. The fatigue strength results show that all coated alloys have reduced strength compared with the uncoated base alloy, which gradually decreases with increasing loads applied to them. It was also discovered that the alloy A4, which contains a high weight fraction of Al2O3, was closest to the base alloy and showed the greatest improvement in fatigue compared to the other alloys.

Keywords: 
thermal spraying, ceramic powders, rotational fatigue, steel alloy AISI1020, bond coat, thermal barrier coating, ni-al cr si powder, Al<sub>2</sub>O<sub>3</sub>+MgO powder.
References: 
1. A. Mazin, A. Mahmood, C.E. Gader, Oxidation Communications, 45(1), 2022.
 
2. Saad Gh. Rifai, Edrees E. Khadeer. J. Engin. Res. Rev., 1(1), 51, 2024.
 
3. Mcgrann, R.T.R., Greving, D.J., Shadley, J.R., Rybicki, E.F., Kruecke, Tl.T., Bodger, B.E. Surface coating technology, 59, 108, 1998.
https://doi.org/10.1016/S0257-8972(98)00665-3
 
4. Osawa, S., Itsukaichi, T., & Ahmed, R., J. Thermal Spray Technology, 14, 495, 2005.
https://doi.org/10.1361/105996305X76513
 
5. Voorwald, H. J. C., Souza, R. C., Pigatin, W. L., & Cioffi, M. O. H., Surface and Coatings Technology, 190(2-3), 155, 2005.
https://doi.org/10.1016/j.surfcoat.2004.08.181
 
6. Tipton, A., The Effect of HVOF Thermal Spray on the Elevated Temperature High Cycle Fatigue Behavior of a Martensitic Stainless Steel. Dresser-Rand, New York, NY., 2002
 
7. La Barbera-Sosa, J. G., Santana, Y. Y., Villalobos-Gutiérrez, C., Cabello-Sequera, S., Staia, M. H., & Puchi-Cabrera, E. S., Surface and Coatings Technology, 205(4), 1137, 2010.
https://doi.org/10.1016/j.surfcoat.2010.01.038
 
8. Ahmed, R., & Hadfield, M., J. Thermal Spray Technology, 11, 333, 2002.
https://doi.org/10.1361/105996302770348727
 
9. Al-Fadhli, H.Y., Stokkes, J., Hashmi, M.S.J., Yillbas, B.S., Surface and Coatings Technology, 200, 2006.
https://doi.org/10.1016/j.surfcoat.2005.08.143
 
10. Alloys, Electrical Resistance. Special-Purpose Materials. 1998.
 
11. Ahmed, B. S., & Jassim, I. K., J. University of Babylon for Pure and Applied Sciences, 27(4), 98, 2019.
 
12. Michalak, M., Sokołowski, P., Szala, M., Walczak, M., Łatka, L., Toma, F. L., & Björklund, S., Coatings, 11(8), 879, 2021.
https://doi.org/10.3390/coatings11080879
 
13. Rana, N., Mahapatra, M. M., Jayaganthan, R., & Prakash, S.,. J. Alloys and Compounds, 615, 779, 2014.
https://doi.org/10.1016/j.jallcom.2014.07.038
 
14. Chatha, S. S., Sidhu, H. S., & Sidhu, B. S., Surface and Coatings Technology, 206(19-20), 3839, 2012.
https://doi.org/10.1016/j.surfcoat.2012.01.060
 
15. Callister Jr, W. D., & Rethwisch, D. G., Fundamentals of materials science and engineering: an integrated approach. John Wiley & Sons, 2020.
 
16. Puntambekar, G.S.Grewal, P.BJoshi and Sampathkumaran. International Journal of Latest Research in Science and Technology, pp.132U, N.-137, 2014.
 
17. Alweendo, S. T., Morita, M., Hasegawa, K., & Motoda, S. Materials, 14(23), 7480, 2021.
https://doi.org/10.3390/ma14237480
 
18. Ahmed, R. & Hadfield, M. J. Thermal Spray Technology, 11(3), 333, 2002.
https://doi.org/10.1361/105996302770348727
 
19. Affonso, Luiz Octavio Amaral. Machinery Failure Analysis Handbook. Gulf Publishing Company, 2013.
 
20. Ana Isabel García-Diez, Juan José Galán-Díaz, Manuel Ángel Graña-López, and Mar Toledano-Prados. Applied Science, 12, 2369, 2, 2022.
https://doi.org/10.3390/app12052369

Current number: