Funct. Mater. 2026; 33 (3): 573-582.

doi:https://doi.org/10.15407/fm33.03.573

3D printing by direct ink writing of heater prototypes for ceramic fuel cells from mechanosynthesized MoSi2 nanopowder

I. Poliakov, V. Naumenko, I. Kud, R. Mediukh, O. Myslyvchenko, Ye. Brodnikovskyi, O. Zgalat-Lozynskyy

Frantsevich Institute for Problems of Materials Science NAS of Ukraine

Abstract: 

This study presents a comprehensive investigation of the mechanosynthesis of molybdenum disilicide (MoSi2) nanopowder and its subsequent application in the fabrication of ceramic heating elements for stacks of solid oxide fuel cells (SOFCs). SOFCs are a promising technology for stationary energy generation due to their high efficiency in converting chemical energy into electricity (up to 65%) and heat (up to 30%), fuel flexibility (hydrogen, hydrocarbons, CO, etc.), and absence of platinum-group catalysts. MoSi2 was selected as a material for heating elements due to its high electrical and thermal conductivity, exceptional thermal stability, resistance to oxidation, and ability to withstand high operating temperatures, making it suitable for rapid and uniform heating in SOFC stacks. The influence of the powder-to-ball mass ratio (1:10 and 1:20) and milling parameters on the mechanosynthesis process was systematically studied. It was found that higher energy input significantly accelerates the formation of the MoSi2 phase, reducing the reaction time by approximately 1.5 times. X-ray diffraction analysis confirmed the formation of the MoSi2 phase with minor residual molybdenum, while silicon was found to be X-ray amorphous, indicating its high reactivity and structural disorder after mechanical activation. Energy transfer during milling and particle size distribution were analyzed to optimize synthesis parameters, ensuring uniform nanopowder morphology suitable for further processing. The synthesized nanopowder was used to prepare ceramic pastes for 3D printing via the robocasting method. The rheological properties of the pastes were optimized to allow stable extrusion and high-resolution printing of complex geometries. Key printing parameters, including extrusion rate, nozzle diameter, and printing speed, were adjusted to minimize defects and ensure the structural integrity of printed elements. After thermal treatment and sintering, the printed heating elements exhibited rapid and uniform temperature rise, demonstrating their suitability for integration into SOFC stacks and other high-temperature energy-generating systems.This work provides a detailed methodology for combining mechanosynthesis and additive manufacturing to produce high-performance ceramic components. The results contribute to the development of energy-efficient and reliable heating elements for advanced SOFCs and demonstrate the potential of MoSi2-based materials in high-temperature energy applications. Furthermore, the findings offer insights into controlling phase composition, particle morphology, and process parameters, which are critical for the scalable production of functional nanostructured ceramics.

Keywords: 
mechanosynthesis, MoSi<sub>2</sub>, additive technologies, DIW, solid oxide fuel cells, 3D printing.
References: 

1. Ulf Bossel, Rapid Startup SOFC Modules, Energy Procedia, Volume 28, 2012, Pages 48-56, DOI: 10.1016/j.egypro.2012.08.039.

2. Polishko, I., Ivanchenko, S., Horda, R., ...Lysunenko, N., Kovalenko, L. / Tape casted SOFC based on Ukrainian 8YSZ powder // Materials Today: Proceedings, 2019, 6, pp. 237–241, DOI: 10.1016/j.matpr.2018.10.100.

3. Afiqa Mohamad, Yuji Ohishi, Hiroaki Muta, Ken Kurosaki, Shinsuke Yamanaka. Thermal and Mechanical Properties of α-MoSi2 as a High-Temperature Material. PSS (Physica status solidi), 2018, vol.225, issue 4, 1700448, DOI: 10.1002/pssb.201700448.

4. Bose S., Hecht R. J. Thermal properties of MoSi2 and SiC whisker-reinforced MoSi2. Journal of materials science, 1992, vol.27, p. 2749-2752, DOI: 10.1007/BF00540701.

5. Sharif A. A. High-temperature oxidation of MoSi2. Journal of materials science, 2010, vol.45, p. 865-870, DOI: 10.1007/s10853-009-4012-8.

6. Serhii Tkachenko, Dmytro Brodnikovskyi, Jan Cizek, Pavel Komarov, Yehor Brodnikovskyi, Yaroslav Tymoshenko, Štefan Csáki, Mykyta Pinchuk, Oleksandr Vasylyev, Ladislav Čelko, Mykola Gadzyra, Tomáš Chráska / Novel Ti–Si–C composites for SOFC interconnect materials: Production optimization // Ceramics International, 2022, 48(19), pp. 27785–27798, DOI: 10.1016/j.ceramint.2022.06.081.

7. Samadzadeh M., Oprea C., Karimi Sharif H., Troczynski T. Comparative studies of the oxidation of MoSi2 based materials: High-temperature oxidation (1000 – 1600 °C). International Journal of Refractory Metals and Hard Materials, 2017, vol.69, p. 31-39, DOI: 10.1016/j.ijrmhm.2017.07.015.

8. Yao Z., Stiglich J., Sudarshan T.S. Molybdenum Silicide Based Materials and Their Properties. Journal of Materials Engineering and Performance, 1999, vol.8, issue 3, p. 291-304, DOI: 10.1361/105994999770346837.

9. Sang Chul Yeo, Soo Wan Jeon, Jung Eun Lee, Vijay Singh, Sang Hwan Kim. Combustion characteristics of molybdenum–silicon mixtures. Ceramics International, 2015, vol.41, issue 1, part B, p. 1711-1723, DOI: 10.1016/j.ceramint.2014.09.113.

10. Ch Gras, D Vrel, E Gaffet, F Bernard. Mechanical activation effect on the self-sustaining combustion reaction in the Mo–Si system. Journal of Alloys and Compounds, 2001, vol.314, issue 1-2, p. 240-250, DOI: 10.1016/S0925-8388(00)01221-4.

11. Kesheng Zuo, Shengqi Xi, Jing’en Zhou. Structure evolution and thermodynamics analysis of MoSi2 during mechanical alloying. Materials Science and Engineering: A, 2007, vol.445-446, p. 48-53, DOI: 10.1016/j.msea.2006.09.002.

12. Malek Ali, Projjal Basu, Marwa Liwa. Effect of Mo-Si Molar Ratio on the Synthesis of MoSi2 Through Mechanical Alloying. Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry, 2013, vol.43, issue 10, p. 1444-1451, DOI: 10.1080/15533174.2012.762783.

13. Peizhong Feng, Akhtar Farid, Xiaohong Wang, Islam S. Humail, Xuanhui Qu. Mechanically activated reactive synthesis of refractory molybdenum and tungsten silicides. International Journal of Refractory Metals and Hard Materials, 2008, vol.26, issue 3, p. 173-178, DOI: doi.org/10.1016/j.ijrmhm.2007.05.008.

14. Hao Liang a, Fang Peng, Haihua Chen, Lijie Tan, Qiang Zhang, Cong Fan, Shixue Guan, Xiaolin Ni, Akun Liang , Xiaozhi Yan, Qiwei Hu. High-pressure sintering of bulk MoSi2: Microstructural, physical properties and mechanical behavior. Materials Science and Engineering: A, 2018, vol.711, p. 389-396, DOI: 10.1016/j.msea.2017.11.016.

15. Yongxia Li, Wenbo Han, Guiqing Chen, Yehong Cheng, Qiang Yang. Effect of in-situ formed MoSi2 on phase transformation and thermal diffusivity of spark plasma sintered silicon nitride. Composites Part B: Engineering, 2017, vol.116, p. 382-387, DOI: 10.1016/j.compositesb.2016.10.080.

16. Hiroyuki Shimizu, Masaru Yoshinaka, Ken Hirota, Osamu Yamaguchi. Fabrication and mechanical properties of monolithic MoSi2 by spark plasma sintering. Materials Research Bulletin, 2002, vol.37, issue 9, p. 1557-1563, DOI: 10.1016/S0025-5408(02)00852-8.

17. Gesheva K.A., Ivanova T., Gogova D., Beshkov G. Formation of MoSi2 by rapid thermal annealing in vacuum of CVD – Mo films on silicon substrate. Vacuum, 2000, vol.58, issue 1-2, p. 502-508, DOI: 10.1016/S0042-207X(00)00212-8.

18. Naumenko, V.Y., Zyatkevich, D.P., Vedel, D.V. et al. 3D Printing of MoSi2-Based Ceramic Heaters Using the Robocasting Method. Powder Metall Met Ceram 63, 343–351 (2024), DOI: 10.1007/s11106-025-00466-4.

19. Naumenko, V.Y., Zyatkevich, D.P., Zgalat-Lozynskyy, O.B. 3D printing technologies using robocasting of ceramic materials based on refractory compounds Mizhvuzivskyi zbirnyk “NAUKOVI NOTATKY”, Lutsk, 2024, No78.- с.78-82, DOI: 10.36910/775.24153966.2024.78.11.

20. Derevianko, O.V., Ivanchenko, S.E., Naumenko, V.Y. et al. Evolution of Rheological Parameters of Chitosan Hydrogel/Silicon Nitride Paste During 3D Printing by Robocasting for Biomedical Applications. Powder Metall Met Ceram 64, 228–242 (2025), DOI: 10.1007/s11106-026-00519-2.

21. Zgalat-Lozynskyy, O.B. Materials and Techniques for 3D Printing in Ukraine (Overview). Powder Metall Met Ceram 61, 398–413 (2022), DOI: 10.1007/s11106-023-00327-y

22. Peng, E., Zhang, D., Ding, J. Ceramic Robocasting: Recent Achievements, Potential, and Future Developments. Adv. Mater. 30, 1802404 (2018). DOI: 10.1002/adma.201802404

23. Feilden, E., Blanca, E. G.-T., Giuliani, F., Saiz, E., Vandeperre, L. Robocasting of structural ceramic parts with hydrogel inks, Journal of the European Ceramic Society, Vol. 36, Issue 10, 2525-2533, (2016) DOI: 10.1016/j.jeurceramsoc.2016.03.001.

24. Zhang, D., Jonhson, W., Herng, T. S., Ang, Y. Q., Yang, L., Tan, S. C., Peng, E., He, H., Ding, J. A 3D-printing method of fabrication for metals, ceramics, and multi-materials using a universal self-curable technique for robocasting. Materials Horizons. Vol. 7, No. 4. P1083–1090 (2020) DOI:10.1039/C9MH01690B

25. Jiang, P.-Z., Deng, Z., Min, P., et al. Direct ink writing of multifunctional gratings with gel-like MXene/norepinephrine ink for dynamic electromagnetic interference shielding and patterned Joule heating. Nano Research. Vol. 17, P. 1585–1594, (2024) DOI: 10.1007/s12274-023-6044-9

Current number: